- On sale!
- -20%
- New
- 20%
AxLR Blood Barbell - 20 kg - Second Hand
€224.17
€179.33 179.33HT Save 20%
AxLR Blood Barbell - 20 kg - Second Hand
This weightlifting barbell is used. It was used on the competitions of the 2022 season. It shows traces of use, and chalk (to be cleaned by you)
The Blood Red Barbell AxLr was designed for your WODs and repeated Weightlifting exercises. You will increase your rep 'thanks to its 4 needles bearings system "made in Germany". The grip of the AxLR men's Bar has been worked for the intense repetition of movements, it will hang without damaging. The Blood Red / Gray finish gives a stylish look, and the galvanized treatment provides an extreme protection against corrosion. A silicone strap has been added to protect the barwhen placed on the ground without weights.
Characteristics:
- Weight: 20kg
- Diameter: 28 mm
- Sleeve diameter: 50 mm
- Tensile Strenght: 190,000 PSI
- Total length: 220 cm
- Shaft Lenght: 131 cm
- Sleeves length: 41,50 cm
- Max load: 700 kg
- Bushings/Bearings: 4 needles Bearings on each sleeve
- Dual Knurl Marks, No Center Knurl
- Shaft Coating: Blood Red Cerakote
- Sleeve Coating: Bright Zinc
Must-have Accessories
Bumpers
Collars
Accessoires
 Ultimate Fractionnal Plates!
Features:
| Fractional Plate - Pair €27.50 | |
Increase your PR's with the change platesThe Change Plates is made of dense resin and high-end products, these additional weights minimize noise when the bar is dropped. Their Collar opening meets IWF standards of 50.1 mm. You will be able to adapt your weight with great precision to respect your loads and work efficiently. Friction Grip Change Plates are essential for all boxers and all athletes who practice often weightlifting.
| Change Plate - Pair €20.83 | |
  Fractional Plates SetLooking for your "Personal Record"? Use these Fractional Plates to gradually load your weightlifting bar. Gradually increase your load, take the good sensations barbell in hand and progress quickly thanks to our fractional set. | Fractional Plates - set 5 kg €57.50 | |
  Technical Weightlifting Bumper Plate!The 2.5kg CrossLiftor Olympic technical plates benefit from a long know-how in the design of weightlifting equipment. These initiation weights are ultra strong and can be thrown to infinity on the ground. Athletes and weightlifters will finally be able to work on bars with lighter loads, at the same height and under the same conditions as with conventional weightlifting discs. Technical bumper features :
| Technical Bumper Plate 2,5 kg €57.50 |
Sol
Rangement
Wall rack for 8-BarbellsWall-mounted storage rack for up to 8 weightlifting bars. Made of resistant steel and with a plastic coating to protect your bars, this rack will efficiently improve your storage space. Height: 140cm Note: storing weightlifting bars horizontally protects the bearings and improves their longevity. | Wall rack for 8-Barbells €90.83 | |
Barbells Storage!
The bottom of the cubic storage has a metal plate thus preventing the bars from touching the ground. Characteristics :
| Cubic storage for 9 Barbells €124.17 | |
The ideal rack for your bumper plates!This storage rack for your disks is great for saving space and keeping a clean wod area. Thanks to this bumper plates storage rack you will bring to your members a real comfort of training. The technical features of this storage rack make it an indispensable piece of equipment for all box owners and gym owners. | Horizontal Bumpers rack €245.83 | |
  Studio Rack very complete!The Studio Storage by CrossLiftor is designed to put the essentials of your equipment in a small space. Its 4 shelves allow you to store kettlebells, dumbbells, Wall Balls, or weightlifting discs, you can place all these items at your convenience. It also has 2 slots for Olympic weightlifting bars at each end. The thickness and sturdiness of the steel of the Studio Storage will guarantee you stability and reliable security. Characteristics :
| Studio Storage Rack €404.17 |
CrossLiftor Olympic Barbell Blood High Intensity
Inspired by current design and technicality trends, CrossLiftor wanted to create the AxLR bar. With a 190,000 PSI tensile strength and selected needle bearings Made in Germany with high quality, the AxLR Olympic Bar will give you an increased performance during your training and a long life even with intensive practice.
The AxLR CrossLiftor bar is produced using high precision machines and demanding specifications, giving the result a high-end weight bar with worked finishes: 4-needle bearings on each sleeve to quickly lock your movements, strong grip without damaged hands, galvanized treatment to avoid rust spots, silicone strap to protect the bar placed on the ground.
Characteristics:
- Brand: CrossLiftor
- Bar Type: men's bar
- Using the bar: weightlifting, powerlifting etc.
- Weight: 20 kg
- Diameter: 28 mm
- Sleeve diameter: 50 mm
- Shaft Coating: Red Cerakote
- Sleeve Coating: Bright Zinc
- Total length: 200 cm
- Shaft Lenght: 131 cm
- Sleeves Length: 31,50 cm
- Coating: Zinc
- Center knurl: no
- Knurl mark: dual
- Bushings/Bearings: 4 needles Bearings on each sleeve
- Tensile strength: 190,000 PSI
- Maximum load: 700 kg
- Use: high intensity
- Quality tested and certified by CrossLiftor Team
Maintenance and storage of your weightlifting barbell:
For optimal operation, it is advisable to lubricate the bearings of your AxLR barbell blood every 6 months. Use a Teflon-type or specialty lubricant for the maintenance of Olympic bars. This lubricant will not obstruct the needles of your bar. It is recommended to store your Olympic bars horizontally and clean them after each workout.
Removing chalk and perspiration will prevent the appearance of rust spots even if your AxLR blood barbell is already treated with anti-corrosion zinc.
Used
Shipping Information
The product is in stock: shipping within 24 to 72 hours.
The product is out of stock : The availability date is displayed under the Pre-order button.
For orders with one or more out-of-stock products and over 500€: shipment of in-stock products within 24 to 72 hours. A second shipment will take place at no extra shipping cost as soon as ALL other out-of-stock products in pre-order are restocked.
For orders with one or more out-of-stock products and under 500€: we will only make one shipment as soon as ALL out-of-stock products are in pre-order. If you want a first shipment of the products in stock, you will have to place 2 orders, one with the products in stock, and another one with the products in pre-order.
All the dates of restocking of out-of-stock products are indicated and updated daily on the product pages on our website and archived in your order history.
After the shipping day, you can add between 1 and 5 days for the goods transit
We offer several delivery solutions depending on the weight of the order and the volume of the parcels. There are many cases, you will be able to consult the delivery method(s) once the products are added to your shopping cart. All the transporters with whom we work deliver your order upon your signature.
Whatever the transporter, you are informed before the day of delivery. For small parcels, you receive an email and/or text message with the day of delivery, which you can modify as you wish. For pallets, the transporter calls you agree on an appointment and a time slot.
We also offer Click & Collect solution for those who do not want to pay shipping costs and move to us in Vitrolles, FRANCE (13127). Once in the delivery solutions, you will just have to select "Click & Collect" and to choose a date and a time slot of withdrawal.
Whatever the carrier, you are notified before the day of delivery. For small parcels, you receive an email and/or text message with the delivery day, which you can modify as you wish.
If you are absent at the time of the delivery, the transporter can let the parcel in a point relay if this one measures less than 120cm height and weighs less than 30 kg. Otherwise, you will be notified to agree a second appointment within 48 hours, without news from you, the parcel will be returned to Crossliftor. You will have to pay the shipping costs again to have the parcel delivered.
For larger parcels and pallets deliveries, the transporter will call you to agree on an appointment and a time slot. If you are absent on the delivery day, you will have to pay the representation fee again, otherwise the order will be resent to Crossliftor.
If you leave in France, nothing could be simpler, once your cart and your account are created, you will be able to choose Click & Collect in the shipping methods. You will just have to enter the day and time of your choice!
We have only one collection point for the moment, in the Crossliftor warehouses in Rognac (13340 - FRANCE) The Click & Collect is open from Monday to Friday included. The schedule will depend on the available slots.
